| B-B18 |
Removable Flash Disk 4GB for ZVA/ZVB with controller unit FMR7/3 or FMR7/6 |
| B-B18 |
Removable hard disk 160GB (including firmware) for R&S® ZVA and R&S® ZVB with FMR7 |
| B-B4 |
Oven quartz (OCXO) for ZVA, ZVB, ZVT |
| B-K2 |
Time domain (for ZVA, ZVB, ZVT) (software license) |
| B-K30 |
Noise figure measurement on 2 port devices (for ZVA and ZVT, |
| B16 |
Direct generator-receiver-access (for 2 port ZVA67) |
| B21 |
Generator Step Attenuator Port 1, mechanical, 50dB in 10dB steps |
| B22 |
Generator Step Attenuator Port 2, mechanical, 50dB in 10dB steps |
| B23 |
Generator Step Attenuator Port 3, mechanical, 50dB in 10dB steps |
| B24 |
Generator Step Attenuator Port 4, mechanical, 50dB in 10dB steps |
| B31 |
Receiver Step Attenuator Port 1, mechanical, 35dB in 5dB steps |
| B32 |
Receiver Step Attenuator Port 2, mechanical, 35dB in 5dB steps |
| B33 |
Receiver Step Attenuator Port 3, mechanical, 35dB in 5dB steps |
| B34 |
Receiver Step Attenuator Port 4, mechanical, 35dB in 5dB steps |
| B7 |
Measurements on pulsed signals. Pulse profile,Recording time up to 25ms, up to 30MHz bandwidth |
| B8 |
External attenuator control. Control unit for electronic attenuators of ZVAZ90E, ZVA-Z110E |
| C3 |
Three years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| C3 |
Three years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| C5 |
Five years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| C5 |
Five years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| DCV-2 |
Documentation of calibration values |
| DCV-ZP |
Printout of DCV (additional, in combination with DCV-Option only) |
| K10 |
Group delay measurement on converters without LO access. For long distances via LXI network of 2 ZVA or ZVT. |
| K17 |
Increases the receiver bandwidth to 5MHz |
| K27 |
Two internal pulse generators (for ZVA and ZVT) |
| K4 |
Frequency converting measurement for ZVA and ZVT |
| K5 |
Phase measurement on mixers (for ZVA, ZVT; ZVA/T-B16 and ZVA-K4 required) |
| K6 |
True Differential Measurements for all 4-port ZVA and for ZVT with at least 3 ports |
| K7 |
Measurements on pulsed signals pulse profile, recording time up to 3ms up to 30 MHz bandwidth |
| K8 |
Control of frequency converters (for ZVA with f>20 GHz, ZVT20, includes ZVA-K4) |
| K9 |
Measurement of group delay on frequency converters without LO access (for ZVA, ZVT; |
| R3 |
Three years of depot repair coverage, including recalibration and test data if necessary to complete a repair - |
| R3 |
Three years of depot repair coverage, including recalibration and test data if necessary to complete a repair - |
| R5 |
Five years of depot repair coverage, including recalibration and test data if necessary to complete a repair - |
| R5 |
Five years of depot repair coverage, including recalibration and test data if necessary to complete a repair - |
| ZV-Z218 |
1,85 mm calibration kit, fixed match, TOSM male and female calibration standards |
| ZV-Z96 |
Flexible Precision Cable 50 Ohm 1.85mm(f)Rugged. to 1.85mm(m)Rugged.DUT; DC to 67GHz; 635mm(25 inch); 1 piece |
| ZVAB-B18 |
Removable Flash Disc for ZVA/ZVB with controller unit FMR7/3 or FMR7/6 |
| ZVAB-B4 |
Oven quartz (OCXO) for ZVA, ZVB, ZVT |
| ZVAB-K2 |
Time domain (for ZVA, ZVB, ZVT) |
| ZVAB-K30 |
Noise figure measurement on linear and frequency converting 2 port devices (for ZVA, ZBV and ZVT, |