| 0-C3 | Three years of depot calibration coverage based on the R&S recommended calibration interval - includes test data. |
| 0-C5 | Five years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| 0-R3 | Three years of depot repair coverage, including standard recalibration and test data if necessary to complete the repair. |
| 0-R5 | Five years of depot repair coverage, including standard recalibration and test data if necessary to complete the repair. |
| 0DKD | FSVR30 DKD(ISO17025) calibration including ISO 9000 calibration (order only with device) |
| B17 | Digital baseband interface, retrofittable, detector board Rev. 05.01 required, |
| B18 | Solid state drive, 8GB, including analyzer firmware, for exchange against standard hard drive |
| B19 | Spare removable hard drive incl. analyser firmware in exchange for standard hard drive |
| B21 | LO/IF connections for external mixers (FSV30 / FSV40) |
| B22 | RF Preamplifier 20 dB, 9 kHz to 7 GHz |
| B24 | RF preamplifier 9kHz to 30GHz (for R&S® FSV30 only) not installable post factory |
| B25 | Electronic attenuator, 1 dB steps |
| B3 | AM/FM demodulator for listening; includes loudspeaker, plug for headphone and volume control |
| B4 | OCXO, precision frequency reference Aging per year: 0.1 ppm |
| B4 | OCXO, precision frequency reference, aging per year: 0.1 ppm |
| B5 | Additional interfaces. IF/Video/AM-FM-demod. output, AUX port, trigger output, 2 additional USB(A) |
| B9 | Tracking generator. 100 kHz - 7 GHz (FSV7 / FSV13 / FSV30); 100 kHz - 3.6 GHz (FSV3) |
| DCV-2 | Documentation of calibration values |
| DCV-ZP | Printout of DCV (additional, in combination with DCV-Option only) |
| FS-B33 | USB mass memory write protection, disables writing to USB memory sticks (ex factory only) |
| K10 | Analysis of GSM, EDGE and EDGE evolution signals |
| K100 | Analysis of EUTRA/LTE FDD downlink signals |
| K101 | Analysis of EUTRA/LTE FDD uplink signals |
| K102 | EUTRA/LTE Downlink MIMO measurement application (R&S®FSV-K100 or R&S®FSV-K104 required) |
| K104 | Analysis of EUTRA/LTE TDD downlink signals |
| K105 | Analysis of EUTRA/LTE TDD uplink signals |
| K30 | Noise figure and gain measurements (Preamplifier R&S®FSV-B22 or R&S®FSV-B24 required) |
| K40 | Phase noise measurement application |
| K54 | EMI application for diagnostic of RF interference with spectrum analyzers R&S®FSV and |
| K70 | Vector signal analysis application for modulation analysis of digital modulated single carrier signals |
| K72 | Analysis of 3GPP-FDD base station signals incl. HSPA+ |
| K73 | 3GPP-FDD UE analysis incl. HSPA |
| K76 | 3GPP TD-SCDMA BTS measurements application |
| K77 | 3GPP TD-SCDMA UE measurement application |
| K7S | FM stereo measurement application, measurement of L, R, M, S and pilot dev, Crosstalk, THB |
| K8 | Bluetooth/EDR measurement application (software license) |
| K82 | Analysis of CDMA2000 base station signals |
| K83 | CDMA2000 MS measurement application (software license) |
| K84 | Analysis of 1xEV-DO base station signals |
| K85 | 1xEV-DO MS measurement application (software license) |
| K9 | Power sensor measurement with NRP power sensors |
| K91 | Analysis of WLAN 802.11a,b,g,j signals |
| K91N | Extension of R&S®FSV-K91 to 802.11n (R&S®FSV-K91 required) |
| K93 | Analysis of WIMAX# 802.16 SISO signals |