| B1 |
Spectrum analyzer module 9kHz - 3GHz |
| B10 |
External generator control |
| B17 |
Digital baseband interface, retrofittable, detector board Rev. 05.01 required, |
| B18 |
Solid state drive, 8GB, including analyzer firmware, replaces standard hard drive |
| B19 |
Second hard disk incl. analyzer firmware for exchange against standard hard disk |
| B2 |
Transfer relay |
| B21 |
LO/IF connections for external mixers (FSV30 / FSV40) |
| B22 |
RF Preamplifier 20 dB, 9 kHz to 7 GHz |
| B24 |
RF preamplifier 9kHz to 40GHz (for R&S® FSV40 only) not installable post factory |
| B25 |
Electronic attenuator, 1 dB steps |
| B29 |
Frequency extension to 20Hz (retrofittable in service center) |
| B3 |
Generator interlock relay |
| B4 |
OCXO, precision frequency reference, aging per year: 0.1 ppm |
| B5 |
Additional interfaces. IF/Video/AM-FM-demod. output, AUX port, trigger output, 2 additional USB(A) |
| B7 |
Option for IMS: Hardware extension for using two power sensors |
| B7 |
Option for IMS: Hardware extension for using three power sensors |
| B70 |
Extension to 40MHz signal analysis bandwidth |
| B9 |
Tracking generator. 100 kHz - 7 GHz (FSV7 / FSV13 / FSV30); 100 kHz - 3.6 GHz (FSV3) |
| C3 |
Three years of depot calibration coverage based on the R&S recommended calibration interval - includes test data. The first calibration is included with product delivery with 2 additional depot calibration(s). |
| C5 |
Five years of calibration coverage based on the R&S recommended calibration interval - includes test data. The first calibration is included with product delivery with 1 additional depot calibration(s). |
| DCV-1 |
Documentation of calibration values |
| DCV-2 |
Documentation of calibration values |
| DCV-ZP |
Printout of DCV (additional, in combination with DCV-Option only) |
| DKD |
FSV40 DKD (ISO17025) calibration incl. ISO 9000 calibration (order only with device) |
| FS-B33 |
USB mass memory write protection, disables writing to USB memory sticks (ex factory only) |
| HA104 |
HF Whip Antenna HA104 1.5MHz to 30MHz, height 5m max. 150W CW/PEP |
| HA230 |
HF Receiving Antenna HA230/403 consisting of: HA230-M (mast) and |
| HA230-M |
Antenna Mast for HA230/403 3 sections, height 6 meters including guy ropes |
| HA230-Z |
Antenne Head for HA230/403 2 x horizontal / 1 x vertical whip length approx. 5 meters |
| HE010 |
Active HF Rod Antenna 9kHz to 80MHz N-female |
| HE016 |
Active Receiving Antenna System vertical polarization: 10kHz to 80MHz |
| HE202 |
Active Receiving Dipole 200 MHz to 1000 MHz N-female |
| HE202Z1 |
Mast Adapter for HE202 and HE302 adapter needed only for special |
| HE202Z2 |
RF Cable with ferrites for HE202 and HE302 for sheath current suppression |
| HE300HF |
Loop antenna as HF option for HE300 9 kHz to 20 MHz (fitting into transport case |
| HE302 |
Active Receiving Dipole 20 MHz to 500 MHz N-female |
| HE309 |
Active vertical dipole 20 MHz to 1300 MHz N-female |
| HE314A1 |
Active Omnidirectional Receiving Antenna 20MHz to 500MHz N-female |
| HE402 |
Active Directional Antenna 20MHz to 87MHz N-female |
| HE500 |
Active Omnidirectional Receiving Antenna 20 MHz to 3000 MHz |
| HE525 |
Active Rod Antenna out of AM524 Antenna System 100Hz to 30MHz |
| HE526 |
Active Dipole Antenna out of AM524 Antenna System 30MHz to 200MHz |
| HE527 |
Active Dipole Antenna out of AM524 Antenna System 200MHz to 1000MHz |
| HF108 |
ILS/VOR Test Antenna 108MHz to 118MHz BNC-female |
| HF214 |
Omnidirectional Antenna 500MHz to 1300MHz horizontally polarized |
| HF902 |
Omnidirectional Antenna 1GHz to 3GHz, horizontally resp. vertically polarized 2 x N-female |
| HF907 |
Double-ridged waveguide horn antenna 800 MHz to 18 GHz, linear polarized broadband transmitting/receiving antenna |
| HF907DC |
SHF Directional Antenna with Down Converter 7.5 GHz to 18 GHz |
| HF907OM |
Broadband omnidirectional antenna 800 MHz to 26.5 GHz, vertically polarized, |
| HFU-Z |
Accessory: Tripod for HFH2-Z2/-Z3 |
| HK001 |
UHF Coaxial Dipole 225MHz to 400MHz, max. 400W, N-female color: squirrel grey (RAL7000) |
| HK012 |
VHF Coaxial Dipole 100MHz to 165MHz, max. 800W, N-female color: squirrel grey (RAL7000) |
| HK014 |
VHF/UHF Coaxial Dipole 100MHz to 1300MHz, max. 400W N-female |
| HK055L1 |
Broadband mobile antenna 27.5 MHz to 600 MHz Color: CARC383 (green) |
| HK055L1 |
Broadband mobile antenna 27.5 MHz to 600 MHz Color: Sand yellow (RAL1002) |
| HK116 |
Biconical Antenna 20MHz to 300MHz, N-female with adapter for tripod HZ-1 |
| HK309 |
Passive Vertical Dipole 20MHz to 1300MHz N-female |
| HL007A2 |
Crossed Log-Periodic Antenna 80MHz to 1300MHz, horizontally resp. vertically polarized |
| HL024A1 |
Crossed Log-Periodic Antenna 1GHz to 18GHz 2 x SMA-female |
| HL024S2 |
Crossed Log-Periodic Antenna 1GHz to 18GHz, with passive polarization network |
| HL024S7 |
Crossed Log-Periodic Antenna 1GHz to 18GHz, with preamplifier (switchable) |
| HL024S8 |
Crossed Log-Periodic Antenna 1GHz to 18GHz, with preamplifier (switchable) |
| HL024S9 |
Crossed Log-Periodic Antenna 1GHz to 18GHz, with preamplifier (permanent) |
| HL025-Z |
Adapter for HL025, HL050, HL024A1 to HFU-Z mast |
| HL033 |
Log. per. broadband antenna 80 MHz- 2000 MHz, N-female, 460 - 120W + 100% AM |
| HL033M |
Adapter for center support of HL033 Log-Periodic Antenna horizontal or vertical polarization |
| HL040 |
Log-Periodic Broadband Antenna 400MHz to 3600MHz, 150W to 50W N-female |
| HL046 |
High Gain Log-Periodic Antenna 80MHz to 1300MHz N-female |
| HL046-P |
Pneumatic polarization control for HL046 |
| HL046E |
High Gain Log-Periodic Antenna 80 MHz to 3000 MHz with pedestal |
| HL050 |
Log-Periodic Antenna 850MHz to 26.5GHz linear polarized |
| HL223 |
Log-Periodic Broadband Antenna 200MHz to 1300MHz with adapter for tripod HZ-1 |
| HL451 |
Log-Periodic HF Antenna Rx: 2MHz to 30MHz Tx: 5MHz to 30MHz |
| HL471 |
Log-Periodic HF Antenna Rx: 3MHz to 30MHz Tx: 7MHz to 30MHz |
| HL562 |
ULTRALOG Antenna Combined Biconical and Log-Periodic Broadband Antenna |
| HL562Z1 |
Tripod for HL562 ULTRALOG Antenna movable |
| HM020 |
Triple Loop Antenna 9kHz to 30MHz, N-female system van Veen/Bergervoet |
| HM020Z1 |
Basic Pedestal for HM020 Triple Loop Antenna for DUT support |
| HM020Z2 |
Adapter Pedestal for HM020 Triple Loop Antenna for raising up the DUT from HM020Z1 |
| HM020Z3 |
Calibration Dipole to HM020 Triple Loop Antenna |
| HM525 |
Active H-Field Measurement Antenna 100Hz to 30MHz N-female |
| HM525Z1 |
Pedestal for H-Field Measurement Antenna HM525 |
| HS9043/9 |
VHF Cavity Antenna Filter 100MHz -156MHz; 50W; 50 ohm cylinder type filter; N-type female |
| HV3004 |
Whip Antenna for manpack; 25 to 88(108)MHz; 20W |
| HV3011 |
Whip Antenna for vehicle use; 1.5 MHz to 30MHz; 400W |
| HX002 |
HF-Dipole with Antenna Tuning Unit automatic tuning in the range 2MHz to 30MHz |
| HX002A1 |
HF-Dipole with Antenna Tuning Unit automatic tuning in the range 1.5MHz to 30MHz |
| HX002F |
Frequency Range Extension for HX002 1.6MHz to 2MHz |
| HX002H1 |
HF Dipole, 150W ground version; with LWL interface; RAL7001 |
| HX002M1 |
HF Dipole with Antenna Tuning Unit 1.5 MHz to 30MHz; naval version; optimized for naval applications by |
| HZ-1 |
Wooden tripod as antenna mount for EMC measurements with HFH2-Z6, HK116, HL223 and HUF-Z4 |
| HZ-10 |
Screened calibrated magnetic field pickup coil 5 Hz - 10 MHz incl. calibration certificate and report |
| HZ-11 |
Probe set for E and H near field measurements, 100 kHz to 2 GHz, battery charger 220 V |
| HZ-11 |
Probe set for E and H near field measurements, 100 kHz to 2 GHz, battery charger 11V |
| HZ-12 |
Precision half-wave dipole set (set of 2 dipoles calibrated) 30 MHz - 300 MHz |
| HZ-13 |
Precision half-wave dipole set (set of 2 dipoles calibrated) 300 MHz - 1000 MHz |
| HZ-14 |
Probe set for E and H near field measurements, 9 kHz to 1 GHz |
| HZ-3 |
Accessory: Supply cable length 3 m for HFH2-Z1, HFH2-Z2, HFH2-Z3 and HFH2-Z6 |
| HZ-4 |
Accessory: Supply-cable (10 m) for HFH2-Z1, HFH2-Z2, HFH2-Z3 and HFH2-Z6 |
| HZ-9 |
Power supply for active antennas HFH2-Z1,-Z2,-Z3,-Z6 (remote operation) |
| IMS |
Integrated measurement system for EMS. For measurements in compliance with civil, automotive and military |
| IMS-DKD |
IMS DKD(ISO17025) calibration incl. ISO 9000 calibration (order only with device) |
| K1 |
Set of cables, for connecting HF907DC to PR100 |
| K10 |
Analysis of GSM, EDGE and EDGE evolution signals |
| K100 |
Analysis of EUTRA/LTE FDD downlink signals |
| K101 |
Analysis of EUTRA/LTE FDD uplink signals |
| K102 |
EUTRA/LTE Downlink MIMO measurement application (FSV-K100 or FSV-K104 required) |
| K104 |
Analysis of EUTRA/LTE TDD downlink signals (for FSV) |
| K105 |
Analysis of EUTRA/LTE TDD uplink signals (for FSV) |
| K14 |
Spectrogram measurement application |
| K30 |
Noise figure and gain measurements (Preamplifier R&S®FSV-B22 required) |
| K40 |
Phase noise measurement application |
| K54 |
EMI application for diagnostic of RF interference with spectrum analyzers R&S®FSV and |
| K7 |
Analog modulation analysis for AM, FM, PM |
| K70 |
Vector signal analysis application for modulation analysis of digital modulated single carrier signals |
| K72 |
Analysis of 3GPP-FDD base station signals incl. HSPA+ |
| K73 |
3GPP-FDD UE analysis incl. HSPA |
| K76 |
3GPP TD-SCDMA BTS measurements application |
| K77 |
3GPP TD-SCDMA UE measurement application |
| K7S |
FM stereo measurement application, measurement of L, R, M, S and pilot dev, Crosstalk, THB |
| K8 |
Bluetooth/EDR measurement application (software license) |
| K82 |
Analysis of CDMA2000 base station signals |
| K83 |
CDMA2000 MS measurement application (software license) |
| K84 |
Analysis of 1xEV-DO base station signals |
| K85 |
1xEV-DO MS measurement application (software license) |
| K9 |
Power sensor measurement with NRP power sensors |
| K91 |
Analysis of WLAN 802.11a,b,g,j signals |
| K91n |
Extension of FSV-K91 to 802.11n (FSV-K91 required) |
| K93 |
Analysis of Wimax 802.16 SISO signals |
| N |
Special Features: DISPLAYED AVE. NOISE LEVEL (DANL): -136DBM, TYP; 40MHZ ANALYSIS BANDWIDTH; +15 DBM THIRD ORDER INTERCEPT (TOI); REMOVABLE HARD DRIVE FOR SECURITY; MEASUREMENT APPLICATIONS FOR VECTOR SIGNAL ANALYSIS |
| N |
Touchscreen for Navy |
| NAS |
Directional power meter display unit |
| NAZ10 |
Termination 50 Ohm, 10 W, 0 - 2 GHz N-connector |
| NAZ30 |
Termination 50 Ohm, 30 W, 0 - 4 GHz N-connector |
| R3 |
Three years of depot repair coverage, including recalibration and test data if necessary to complete the repair. First year of repair coverage is provided by the 12-month new product warranty. |
| R5 |
Five years of depot repair coverage, including re-calibration if necessary to complete the repair. First year of repair coverage is provided by the 12-month new product warranty. |
| U1 |
Upgrade to dual core CPU processor |
| Z1 |
Adapter for HF907DC to wooden tripod HZ-1 |
| Z10 |
Carrying bag for NAS |
| Z2 |
Carrying case for HF907DC and accessories |
| Z6 |
Active rod antenna 9 kHz - 30 MHz according to MIL and DEF standards |
| Z9 |
Cable (1.5 m) for NAS insertion unit |